Log In

Home

Previous: Proposed projects

Next: Project preferences

Proposed projects for honours students in 20192

	A/Prof Rini Akmeliawati
	3026 Optimized Operation of Adelaide-Mannum Water Distribution: SA Water Study Case
	3027 Visual-servoing control of a robotic arm for object grasping
	3028 System Identification and Modelling of a Flapping Wing model
	A/Prof Maziar Arjomandi
	2990 Wind tunnel experimentation of wind loads in a heliostat field
	2991 Aerodynamic study of a free-falling particle solar receiver
	2992 Design, build and test a concentrated photovoltaic reciever
	2993 Development of a test facility for study the cardiovascular system
	2994 Micro-channels for hydrogen production
	Dr Cristian Birzer
	3014 Analysis of the Silverfire Cookstove
	Prof. Ben S. Cazzolato
	3000 Electrodynamic loudspeaker driver mechanical suspension modelling and optimization (Industry sponsor: Kyron Audio)
	Dr Lei Chen
	3007 Navigation planning and control of a robotic grass cutter (Industry sponsor: Adelaide Cemeteries Authority)
	3008 Nitrogen gas modelling for wine tank farm (Industry sponsor: Vinpac)
	3009 Adhesive parameter study for Labelling testing and control (Industry sponsor: Vinpac)
	3016 Intelligent airconditioning solutions for fresh healthy veg. (Industry sponsor: Taylor Farms)
	3018 Improving performance of indirect evaporative coolers
	3036 Virtual reality for mining machinery maintenance.
	Dr Rey Chin
	2975 Drag measurement and reduction using Graphene on Oil tankers
	2978 Building and testing of a scaled model wind farm
	2979 Morphing wings UAV
	2980 Turbulence over rough wall flows
	2981 Advanced measurement of stenosed arteries
	Eric Fusil
	3022 Submarine Design Creator
	3024 Submarine analytical tool
	3025 Redesigning and building submarine models and predicting/testing maneuvering performances
	Dr Mergen Ghayesh
	3050 Nonlinear dynamics of nanosystems
	A/Prof Reza Ghomashchi
	3037 Hydrogen Assisted Cold Cracking of Quenched and Tempered steels
	A/Prof Eric J. Hu
	2973 Investigation of flash evaporation in a solar desalination and cooling system induced by steam jet.
	3005 Thermal Diode Tank (TDT)
	3033 A numerical investigation into the forces on and wave making effects of a raised submarine mast
	Dr Mehdi Jafarian
	3011 Hydrogen production through pyrolysis of methane
	3012 Development of a solar indirectly heated receiver for heating gases
	A/Prof Richard Kelso
	3034 Equine Gastro Pump
	Prof Andrei G. Kotousov
	3001 Nondestructive Testing of Structures using Rayleigh Waves (Industry sponsor: SA Power Network)
	3002 Design and build corrosion inspection device for Stobie Poles (SA Power Network) (Industry sponsor: SA Power Network)
	3003 Evaluation of structural life and development of advanced design procedures for structural plastic materials (Industry sponsor: Philmac Pty Ltd)
	3004 Development of a new testing tool using Digital Image Correlation
	Dr Tien-Fu Lu
	2997 Investigate continum robotic arm trajectory planning for fruit picking
	2998 Star tracking jitter motion compensation for precision imaging
	2999 Understand the leak/blockage physical charateristics of irrigation dripper line network
	3031 An investigation of the effectiveness of signal input parameters for piezoelectric based acoustic ultrasound cavitation
	Dr Mohsen Sarafraz
	2987 Design, fabricate and test a photovoltaic/Thermal system:Energetic performance assessment
	2988 Fabrication of a miniaturized noiseless CPU cooling system for micro-electronics and chip-set
	2989 Development of a mid-temperature waste heat recovery system using heat pipes
	Dr Nataliia Sergiienko
	2995 Wave flume experiments of the wave energy converter
	2996 Attitude determination and control of a CubeSat
	Dr Zhiwei Sun
	2984 Simultaneous visualization of small and large particles in turbulent flow
	2986 Tracking single particle in high loading flows
	Dr Zhao F. Tian
	2983 Studies of fires in a cabin
	3029 Flows in Solar receivers
	A/Prof Ling Yin
	3020 3D Laser-Based Printing of Titanium Dental Implants
	3021 Mechanical Testing, CAD/CAM Milling & Ultrasonic Assisted Machining of Dental Ceramics
	3023 Mechanical Testing and Ultrasonic Assisted Machining of New Semiconducting Materials

Legend: Accepted into project Awaiting acceptance Rejected from project

Email all supervisors